manualshive.com logo in svg

ALDI WORKZONE HBS20, Руководство пользователя

Поделиться
Скачать
ALDI WORKZONE HBS20 Скачать руководство пользователя страница 18

23

AFTER SALES SUPPORT

 

 

1300 855 831

 

[email protected]

MODEL: HBS20    PRODUCT CODE: 60339  04/2018

AUS

HBS20

Attachment

Which saw band to use

•  The saw band supplied in the bandsaw is intended for universal use. The following 

criteria should be considered when selecting the saw band: 

•  It is possible to cut tighter radii with a narrow saw band than with a wide saw band.
•  A wide saw band is used if a straight cut is required. This is important in particular 

when cutting wood. The saw band has a tendency to follow the wood grain and 
therefore deviates easily from the desired cutting line. 

•  Fine-toothed saw bands cut more smoothly, but also more slowly than coarse 

saw bands.

•  ATTENTION!

 Never use bent or torn saw bands!

Replacing the saw band (Fig. 1a+1b+14) 

•  Set the top saw band guide (5) at approx. half height between the saw table (7) 

and machine frame (15). 

•  Undo the cover locking mechanisms (10) and open the side covers (11). 
•  Remove the U-reinforcement (34).
•  Relieve the saw band (21) tension by turning the clamping screw (1) anti-clockwise. 
•  Remove the saw band (21) from the saw band rollers (2+8) and through the slot 

in the saw table (7). 

•  Place the new saw band (21) centrally on both saw band rollers (2+8). The teeth 

of the saw band (21) must point downwards in the direction of the saw table.

•  Tension the saw band (21). 
•  Close the side cover (11) again. 
•  Re-install the U-reinforcement (34).

Replacing the table insert (Fig. 13)

•  In case of wear or damage, the table insert (6) must be replaced; otherwise there 

is an increased risk of injury. 

•  Remove the worn table insert (6) by lifting it up and out. 
•  Installation of the new table insert takes place in reverse order.

Extraction nozzle (Fig. 1b)

•  The bandsaw is equipped with an extraction nozzle (19) Ø 40mm for chips.
•  Only operate the device with a suitable extraction system. Check and clean the 

suction channels at regular intervals.

Push rod retainer (Fig. 12)

•  The push stick retainer (48) is pre-mounted on the machine frame. If unused, the 

push stick (26) must always be stowed in the push stick retainer. 

Содержание WORKZONE HBS20































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды