manualshive.com logo in svg

ALDI WORKZONE HBS20, Руководство пользователя

Поделиться
Скачать
ALDI WORKZONE HBS20 Скачать руководство пользователя страница 12

17

AFTER SALES SUPPORT

 

 

1300 855 831

 

[email protected]

MODEL: HBS20    PRODUCT CODE: 60339  04/2018

AUS

HBS20

Safety regulations

•  Give these safety regulations to all persons who work on the machine.
• 

Do not use this saw to cut fire wood.

•  The machine is equipped with a safety switch to prevent it being switched on again 

accidentally after a power failure.

• 

Before you use the machine for the first time, check that the voltage marked on 

the rating plate is the same as your mains voltage.

•  If you use a cable reel, the complete cable has to be pulled off the reel.
•  Persons working on the machine should not be distracted.
•  Note the direction of rotation of the motor and blade.
• 

Never dismantle the machineʼs safety devices or put them out of operation.

•  Never cut workpieces which are too small to hold securely in your hand.
•  Never remove loose splinters, chips or jammed pieces of wood when the saw 

blade is running.

•  It is imperative to observe the accident prevention regulations in force in your area 

as well as all other generally recognized rules of safety.

•  Note the information published by your professional associations.
•  Adjustable protective devices have to be adjusted as close as possible to the 

workpiece.

•  Important! Support long workpieces (e.g. with a roller table) to prevent them sag-

ging at the end of a cut.

•  Make sure the saw band guard (4) is in its lower position when the saw is being 

transported.

•  Safety guards are not to be used to move or misuse the machine.
•  Blades that are misshapen or damaged in any way must not be used.
•  If the table insert is worn, replace it.
•  Never operate the machine if either the door protecting the blade or the detach-

able safety device are open.

•  Ensure that the choice of blade and the selected speed are suitable for the ma-

terial to be cut.

•  Do not begin cleaning the blade until it has come to a complete standstill.
•  For straight cuts of small workpieces against the longitudinal limit stop the push 

stick has to be used.

•  The saw band guard should be in its lowest position close to the bench during 

transport.

•  For miter cuts when the table is tilted, the parallel stop must be positioned on the 

lower part of the table.

•  When cutting round timber, use a suitable holding device to prevent the work-

piece turning.

Содержание WORKZONE HBS20































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды