4
Instructions for operation
English
Uso Vasche IDROP / DIGIT - Code 10004904 - Edition 3 - 09/2007
7
A
P
A'
L
15'
disinfection cycle cannot be started inadvertently
while the tub is in use.
LED “
D
”, which
fl
ashes during the selection phase,
now remains lit and the cycle starts.
For the Professional disinfection system, check
that water mixed with disinfectant is delivered by
all the nozzles. If one of the nozzles delivers more
solution than the others, reduce the
fl
ow.
The automatic disinfection cycle lasts for
two minutes and, once started, cannot be
interrupted.
Now you are ready to enjoy the bene
fi
cial effects
of a soothing hydromassage and the unbeatable
effects offered by your Albatros tub.
ACEX LEVEL and ACEX CLEAN models
The controls for the
ACEX Level
and
ACEX
Clean
systems are described below:
P
:
Starts and stops the hydromassage
system.
A
ʼ
-A
: Adjusts the quantity of air, with the
possibility of different intensities for the
feet and the back/sides.
L
:
This LED lights to indicate that the
appliance is on.
As soon as the appliance is switched on
and while the hydromassage system is in
operation, this LED lights
yellow
.
If the level of water in the tub is not suf
fi
cient
to start the hydromassage system, this
LED lights
red
.
When the correct level is reached, it lights
green
.
Timer
The tub also features a timer which automatically
stops the hydromassage cycle after 15 minutes.
This time cannot be modi
fi
ed.
To restart the cycle, simply press
P
.
Starting and stopping the hydromassage
cycle
To start or stop the hydromassage cycle, press
“
P
”. The cycle, which can be interrupted manually
at any time by pressing “
P
” again, will be
interrupted automatically after 15 minutes.
To prolong the cycle, press “
P
” again.
To select an even more personalized
hydromassage, you can use knobs
A
and
A
ʼ
to adjust the quantity of air delivered by the
hydromassage nozzles. After a hydromassage
session, check that all the nozzles are open
and exit the tub. Using the special tool, start the
disinfection system to clean the internal parts of
the hydromassage circuit.
The duration of the disinfection cycle is
approximately 2 minutes and, once started, the
cycle cannot be interrupted.
Now you can turn the main switch to “OFF”.
Disinfection cycle for models with Acex
Clean system
The disinfection system ensures maximum
hygiene and prolongs the life of the hydromassage
circuit by cleaning the internal parts that cannot
be reached during normal cleaning.
To avoid wasting water, you can use the water
used for your hydromassage.
Before starting the cycle, during which there must
be nobody in the tub, remember to check that all
the nozzles are open.
Then,
fi
ll the reservoir (refer to the instructions).
Place the special key on the symbol on the edge
of the tub twice within not more than 5 seconds.
If this interval is exceeded, the disinfection cycle
will not start.
N.B. This procedure is a safety feature designed
to ensure that the disinfection cycle cannot
be started inadvertently while the tub is in
use.
The duration of the disinfection cycle is 2 minutes;
once started, the cycle cannot be interrupted.
If the disinfection cycle does not start, check that
there is disinfectant in the reservoir and that the
level of water is at least 5 cm above the sensor
or the hydromassage nozzles.
Filling the disinfectant reservoir
To
fi
ll the disinfectant reservoir, remove the cap
located on the lip of the tub and introduce 1 litre
of disinfectant.
The recommended disinfectant solution, which
is available through our authorized dealers and
Service Centres, not only sanitizes the appliance,
but also prevents fermentation and unpleasant
odours, and inhibits the formation of algae and
mildew. The capacity of the disinfectant reservoir
is suf
fi
cient for 12 cycles.
IMPORTANT!
Do not use products containing chlorine
(Amuchina, Bleach etc.) as these may
damage the system and cause leakage of
disinfectant.
Содержание Kellia Combi 170
Страница 6: ......
