Alaxala AX3630S Скачать руководство пользователя страница 864

Страница: 864 / 875

40. Error Messages Displayed When Editing the Configuration

836

40.1.19 MAC-based authentication information

Table 40-19:

MAC-based authentication error messages

40.1.20 Authentication VLAN information [OP-VAA]

Table 40-20:

Authentication VLAN error messages

Relations between IGMP snooping and

authentication ip access-list configuration

are inconsistent.

An authentication access list command and IGMP snooping cannot be used

concurrently on the same device.

Relations between IGMP snooping and

web-authentication configuration are

inconsistent.

Web authentication and IGMP snooping cannot be used concurrently on the

same device.

Relations between the authentication

force-authorized vlan configuration and the

dot1q vlan configuration are inconsistent.

When you specify a post-authentication VLAN in the configuration for

forced authentication in dynamic VLAN mode, you cannot set a VLAN ID

specified by the

switchport mac dot1q vlan

command.

Relations between the vlan configuration

and the authentication force-authorized

vlan configuration are inconsistent.

When you specify a post-authentication VLAN in the configuration for

forced authentication in dynamic VLAN mode, the VLAN ID you specify

must have been registered as a MAC VLAN.

Relations between the web-authentication

configuration and the channel-group

configuration within same port.

A port channel configuration and a Web authentication configuration cannot

be set for the same port.

Relations between the web-authentication

configuration and the VLAN mode

configuration are inconsistent.

Web authentication cannot be set for a port whose VLAN mode is either

tunneling mode or protocol-based VLAN mode.

Relations between the web-authentication

dynamic VLAN mode and the

web-authentication static VLAN mode are
inconsistent.

Web authentication configurations specifying different modes (fixed and

dynamic VLAN modes) cannot co-exist on the same device.

Relations between the web-authentication

logout polling configuration is inconsistent.

Processing cannot continue because there are inconsistencies between

configurations for the Web authentication polling functionality.

Message

Description

Inconsistency is found between the VAA configuration and
the mac-authentication configuration.

The MAC-based authentication activation command
cannot be executed if the

FENSE

command has been set.

Relations between IGMP snooping and mac-authentication

configuration are inconsistent.

MAC-based authentication and IGMP snooping cannot be

used concurrently on the same device.

Relations between the mac-authentication configuration and

the channel-group configuration within same port.

A port channel configuration and a MAC-based

authentication configuration cannot be set for the same

port.

Relations between the mac-authentication configuration and

the VLAN mode configuration are inconsistent.

MAC-based authentication cannot be set for a port whose

VLAN mode is either tunneling mode or protocol-based

VLAN mode.

Relations between the mac-authentication configuration and

the web-authentication dynamic VLAN configuration are

inconsistent.

Configurations specifying legacy mode for MAC-based

authentication and Web authentication cannot co-exist on

the same device.

Message

Description

fense: duplicate server address

<server

address>

The IP address set in the

fense

server

command is the same as the IP

address set for another VAA ID.

Message

Description

Содержание AX3630S












































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AX3630S

Отзывы:

Похожие инструкции для AX3630S

Бренды по названию

Популярные бренды

Alaxala AX3630S, Руководство пользователя программного обеспечения

Результаты поиска

Содержание AX3630S

Отзывы:

Похожие инструкции для AX3630S

Бренды по названию

Популярные бренды