Alaxala AX3630S Скачать руководство пользователя страница 849

Страница: 849 / 875

40. Error Messages Displayed When Editing the Configuration

821

40.1.10 Spanning Tree information

Table 40-10:

Spanning Tree error messages

Relations between vlan in dot1q

configuration and mac vlan configuration are

inconsistent.

switchport mac dot1q vlan

and

switchport mac vlan

cannot be

set because they use the same VLAN.

Relations between vlan in dot1q

configuration and native configuration are

inconsistent.

switchport mac dot1q vlan

and

switchport mac native vlan

cannot both be configured because they specify the same VLAN.

Relations between vlan in mac-address-table

static configuration and switchport

configuration are inconsistent.

The

mac-address-table

static

VLAN specification and the

switchport

configuration do not match. A VLAN set by using

mac-address-table

static

must be specified for

switchport

access

switchport

trunk

allowed

vlan

of the interface that has been set.

Relations between vlan-tunneling and IP

configuration are inconsistent.

VLAN tunneling information and IP information are inconsistent. When

VLAN tunneling is set, IP information cannot be set.

VLAN is not MAC VLAN.

A VLAN specified by

switchport

mac

vlan

is not a MAC VLAN.

Specify a MAC VLAN.

VLAN is not Port VLAN.

The specified VLAN is not a port VLAN.
Specify a port VLAN.

VLAN is not Protocol VLAN.

A VLAN specified by

switchport

protocol

vlan

is not a protocol

VLAN.
Specify a protocol VLAN.

Message

Description

Can not configure spanning-tree when gsrp

is configured.

The Spanning Tree Protocol cannot be set because GSRP is set.

Cost is over 65535, please set up in 1 to
65535 or set pathcost method to long.

The value for

cost

is equal to or greater than 65535. Set the

cost

value

from 1 to 65535 or set

long

for

pathcost

method

Maximum number of MST instance are

already defined.

The number of MST instances has already reached the maximum number.

The maximum number of MST instances that can be set is 16.

Pathcost method is short, please set up in 1 to

65535 or set pathcost method to long.

short

is set for

pathcost

method

. Set the

cost

value from 1 to 65535 or

set

long

for

pathcost

method

Relations between PVST+ and the
protocol-vlan or mac-vlan configuration are

inconsistent.

PVST+ and a protocol VLAN or a MAC VLAN cannot be set concurrently.

Relations between vlan-tunneling and
spanning-tree configuration are inconsistent.

The VLAN tunneling configuration does not match the Spanning Tree
configuration. When a VLAN tunneling configuration is set, the Spanning

Tree Protocol must be stopped.

spanning-tree: maximum number of MST
instance are already defined.

The number of MST instances has already reached the maximum number.
The maximum number of MST instances that can be set is 16.

Message

Description

Содержание AX3630S












































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AX3630S

Отзывы:

Похожие инструкции для AX3630S

Бренды по названию

Популярные бренды

Alaxala AX3630S, Руководство пользователя программного обеспечения

Результаты поиска

Содержание AX3630S

Отзывы:

Похожие инструкции для AX3630S

Бренды по названию

Популярные бренды