Alaxala AX3630S Скачать руководство пользователя страница 478 | Manualshive

Страница: 478 / 875

background image

19. QoS

450

packets is controlled so that packets are distributed evenly. When

<packet>

is specified,

weighted (number of packets) round robin is used. If there are packets in multiple queues,

packets are sent according to the number of packets set for

<packet>

as the queues are

looked at in order. A number from 1 to 8 suffixed to

<packet>

indicates the queue

number.
1.

Default value when this parameter is omitted:

<packet>

:This parameter cannot be omitted.

Note, however, that all

<packet>

values can be omitted. If they are omitted, round

robin is used.

2.

Range of values:

<packet>

:1 to 15

wfq [ min-rate1

<minimum rate1>

] [ min-rate2

<minimum rate2>

] [ min-rate3

<minimum

rate3>

] [ min-rate4

<minimum rate4>

] [ min-rate5

<minimum rate5>

] [ min-rate6

<minimum rate6>

] [ min-rate7

<minimum rate7>

] [ min-rate8

<minimum rate8>

]

Weighted fair queuing. The number of queues is fixed to 8 per physical port. The

minimum guaranteed bandwidth, which is specified for each queue as

<minimum rate>

,

is sent for packets. Note that a number from 1 to 8 suffixed to

<minimum rate>

indicates

a queue number.
1.

Default value when this parameter is omitted:

<minimum rate>

: None. (A minimum guaranteed bandwidth is not set.)

2.

Range of values:

<minimum rate>

: See the table below.

You can specify k (default), M, or G for the unit of the value.
{

<minimum rate>

|

<minimum rate>

M |

<minimum rate>

G }

Specify

<minimum rate>

values so that their total value does not exceed the line

bandwidth.

Table 19-21:

Range of values for the minimum guaranteed bandwidth

#1: 1G is treated as 1000000000, 1M is treated as 1000000, and 1k is treated as 1000.
#2: When setting a value of 1000 kbit/s or more, specify the value in 100 kbit/s increments (1000,

1100, 1200...10000000).
#3: When setting a value less than 1000 kbit/s, specify the value in 64 kbit/s increments (64, 128,

192...960).

2pq+6drr

<byte1>

<byte2>

<byte3>

<byte4>

<byte5>

<byte6>

Top-priority queues and weighted (number of bytes) round robin. The number of queues

is fixed to 8 per physical port. If there are packets in top-priority queue 8, the applicable

packets are sent at the highest priority. The applicable packets in queue 7 are sent at the

next priority after queue 8. If there are no packets in queues 8 and 7, packets are sent until

Setting unit

#1

Setting range

Increment

Gbit/s

1 G to 10 G

1 Gbit/s

Mbit/s

1 M to 10000 M

1 Mbit/s

kbit/s

1000 to 10000000

100 kbit/s

#2

64 to 960

64 kbit/s

#3

«
...
476
477
478
479
480
...
»

Содержание AX3630S












































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AX3630S

Бренд: Gefen Страницы: 11

xStack DES-3500 Series

Бренд: D-Link Страницы: 260

DXS-3600 Series

Бренд: D-Link Страницы: 48

DXS-3400 SERIES

Бренд: D-Link Страницы: 3

Web Smart Switch DGS-1210-16

Бренд: D-Link Страницы: 71

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 56

xStack DES-3800 Series

Бренд: D-Link Страницы: 326

xStack DES-3526

Бренд: D-Link Страницы: 222

Бренд: D-Link Страницы: 2

DXS-1210 Series

Бренд: D-Link Страницы: 20

Бренд: N-Tron Страницы: 18

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

IO-Link BNI LH1-303-S11-K091

Бренд: Balluff Страницы: 12

S5800-EI Series

Бренд: H3C Страницы: 61

Бренд: Dexon Страницы: 31

EdgeLens INT10G8SR56

Бренд: Garland Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды