Akai PDP4225M, Руководство по обслуживанию, Страница: 60 / 77

FHP A3 PANEL DATASHEET
WARNINGS / CAUTIONS / NOTICES
7 0 PREVENT TOsslE-LE DANGER. DAMAGE AND BODILY HARM WHEN E I T O G I H E PLASMA
DISPLAY MODULE. ELEASE CONSIDER AND OBSERVE AIL WARNINGS CAUTIONS AND NOTICES
CONTAINED IN THIS SECTION.
TIilg. sector, Li described based or, the fo.louina two cor, 10
]
>
0 : EC
:
1. EC Product lia b ility ( P L ) ( Council Directive 5 j EEC of 2? Jtdv 1=3? )
1 General Product Safety ( Council Directive
92:59 EEC )
Contents of ± is :■: r,ot specification
'y:X
the cusroiner is requeued, to isree that ?H? dc not take ju v
responsibility Lf tL;e PDF is 'j.sed beyond 'Jie content1; o f ± is and. then leid to icciden:.
Warnings
E
¿
i
JJ
i
.
ii
<■ l-
■
I
k
i.’
I die following warnings when handling fiiePDP module
could
result
J
i i
Injury
o r
even death
1. Caution is reqidred when 1 in idling the PDP module because Li controlled by v* -r. high voltage lUppi ■ -k.
300 V). If you need lo tiadudJc- the module while LI Is sdll operadngor after Ji lias just bcr-fti powered off, guard
against electric Mit.-k by never touclilng die module's drive circuitry areas or LK metallic parts. The
capacitors in the drive circuitiy areas remain temporarily cltarged even after Uie fiowor is turned c-JJ. and u
U u ■
1
e&Ldual voltage is *>1roi ig enougf
1
. Lr can ca use elect i Jl sliock. TlienTore, aft*
1
turning t he fitr.\ i r off. yon
must wait ai least i.-n- minute before touclilng the module
2.
Do not L Lie any or tier power supply voltage for tlie PDP module than die specified voltage in I lift product
specificlil l- -i
1
. Any deviation from the produci sp<'ciflc nl Jc.-n could t ause 11
v.■
product lo fail.
3. Do not operate or Install tlie PDP module under conditions that deviate from Its environmental
\\ -
JfJcatJou
because doing so coidd result in electric shock or product failure Inappropriate DondJUons include moisture,
rain, or near water sources isucti
n
batli tub. laundry lu ll kitchen sink, wet basement, swimming pool)
and ¿ilv.' near fire or heat sources (such a-> near oi' over a radiator or heat resistor or even direct sunlight or
ai iv set
111
ig where 11 iei e Is extreme I is at).
-I. ll' any foreign objects such as liquids (Including water), metallic chips, or dust fall into the PDP module.
In lined lately turn (.'11 111- power supply volt age. Also, never push objects of any kind Lino I In - PDP module
since they may come in contact w ld i dangerous voltage points or < reace sliort circuits that could residl in a
fire hazard or electric
5
] »ck.
S.
If any smoke, offensive smell. or unusual noise comes from the PDP module and also llu- PDP screen doe**
nol display li picture after power-on orw lille operadng. Inunedlately turn off die module’s power supply due
1
11
risk ■ ■! l 1« u lc shock. Never ct
1
itiiun iiperating die PDP modi.de under tJiese codididons.
fj. [>:i not disconnect or connect the PDP module's com lector while llu- power supply Is on or just after power-cdl
■Aie
10
risk of electric si
10
c k. Be'cai i^e die PDP mt)dLdc■ !■> oj > in 1
1
’.1 I Ugl
1
volt age. tlie (1l ive c 1l '. ult cajhcil
0 1
s
remain temporarily charged even after llu- power Is turned off. U you n ^ d to disconnect or ccduicct die
module, wait at least one minute aftei' power-off.
7. D ) nol disconnect or coiuiect the p:jwer coduiectoi' If v iur I iai ids are damp due t- ■ iJskof eleclr it ■ k
8.
D j not damagi -ol niodlfy llu - potver c able of the PDP module due lo rl^k of electric -^1
10
c k.
■T ll die power connector Is covered ^u h dust or dirt wipe il with a dry cloth before powering on llu - display
Because il could causes fire hazard.
5 6 / 7 3