AJ Aircraft 93 AJ Laser 230z Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 25

AJ Aircraft 93 AJ Laser 230z Скачать руководство пользователя страница 5

aj-aircraft.com

Page 4

Optional Servo Configurations

You have the option of using a pull-pull rudder servo or a push-pull rudder servo setup. Fasteners, control horns and
servo connecting rods are provided for optional rudder

setup.

Tools Needed

Blue Painter’s Masking Tape
Thin CA Glue
30 Minute Epoxy
Denatured Alcohol
Paper Towels
Removable Thread Locker (Loctite 242, Blue)
Metric & Imperial Allen Wrenches
Hobby Knife & Fresh Blades
Covering Iron (Trim Iron)

Clamps
Small Flat File
Electric Drill w/ Assorted Small Bits (1/16”, 5/64”)
Small Flat Blade Screwdrivers
Small Phillips Screwdriver
Sandpaper (150-220 Grit)
Pliers
Measuring Tape & Ruler

Inspection

We believe we offer the highest quality kits available. However you may find some minor blemishes, fractures or joint
separations in the construction of our models. Many of these can be easily repaired by backing up the joint or break
with balsa or hard balsa sticks without affecting the performance or appearance of the aircraft.

Take the time to inspect the components of the aircraft.   Inspect the fuselage for any interior joints that may have
loosened as a result of shipping & handling. Apply thin CA glue around the joints of the fuselage core, firewall, fuselage
formers, and rudder servo tray to strengthen.  Allow glue to wick down into joints but be careful to not allow CA glue to
drip or puddle on covering material.  Periodically inspect joints as you fly your airplane. Vibration and repetitive
extreme maneuvers my cause a joints to loosen over time.

«
...
3
4
5
6
7
...
»

Содержание 93 AJ Laser 230z


























Отзывы:

Нет отзывов