manualshive.com logo in svg

Airspan AirSpeed 1030 B48, Руководство по установке

Поделиться
Скачать
Airspan AirSpeed 1030 B48 Скачать руководство пользователя страница 44

 AirSpeed 1030 B48 Installation Guide 

DUG01623

 

Airspan Commercial and Internal Use 

42 

 

 

 

Figure 51: Secure Housing Lock 

 

 

 

Note:

 When securing the cable verify there is no tension on the connector so that it is easy to 

disconnect and re-connect for future maintenance actions.  

5.5 Remote (External) Antenna Assembly 

Note:

 External antennas connected to AirSpeed 1030 B48 should be DC grounded.  

 

 

Caution:

 Power down the AirSpeed unit prior to disconnecting the antenna, to prevent damage.  

The AirSpeed 1030 B48 unit can utilize remotely attached antennas. 

For installation of the remotely mounted antennas follow the antenna manufacturer’s instructions and 
connect the antenna to the AirSpeed 1030 B48 using the appropriate cables. (Weather-proofed N-
type Heliax RF cables (ordered separately). 

1.  Carefully unscrew and disconnect each of the RF cables which connect the integrated 

antenna to the unit. 

 

Figure 52: Antenna RF Cables 

 

  

2.  Screw on a protective cap(s) on the integrated antenna cable, to prevent environmental 

damage, in the event they need to be re-connected. Weather-proof the caps (with a layer of 
self-amalgamating tape followed by an over layer of PVC tape). 

3.  Gather the cables securely together to prevent damage. 

4.  Attach, connect and secure the RF cable(s) between the external antenna and the 

appropriate RF connection on the top of the unit. 

5.  Weather-proof all cable connections, with a layer of self-amalgamating tape followed by an 

over layer of PVC tape. See 

Weather-proofing Antenna Connections

. 

 

 

Содержание AirSpeed 1030 B48


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды