manualshive.com logo in svg

Airspan AirSpeed 1030 B48, Руководство по установке

Поделиться
Скачать
Airspan AirSpeed 1030 B48 Скачать руководство пользователя страница 29

 AirSpeed 1030 B48 Installation Guide 

DUG01623

 

Airspan Commercial and Internal Use 

27 

 

 

4.4 Pole Mounting Assembly 

Caution:

 Mount the AirSpeed 1030 B48 unit in an orientation such that it

’s ports (located on the 

bottom) face downwards. This prevents rain water from settling on the port, and thereby, avoiding 
damage to the unit such as corrosion and electrical short

–circuiting. 

The following describes the pole mounting procedure: 

1. 

Select the location on the pole to mount the AirSpeed 1030 B48 mounting bracket.  

2. 

Position the mounting bracket onto the pole at the required height. 

3. 

Insert the clamp bands by passing them through the upper and lower slots in the bracket, in 
two (2) places 

4. 

Assemble the 2 SEMS screws (M8 x 20) into the lower threaded holes on the mounting 
(base) bracket, do not tighten. 

5. 

Carefully align and position the unit so that the screws (1 on each side) fit into the notched 
grooves provided on the back bracket (pre-assembled on the unit) and hand tighten. Insert 
the M8 screws, washers and nuts (supplied) and fasten the back bracket (pre-assembled on 
the unit) to the mounting bracket. 

6. 

Adjust the unit so that the GPS is positioned upright. Check and tighten all fixing screws. 
(Tighten to a torque of no more than 12.5 Nm (9.22 ft-lb) max.) 

 

Figure 8: Pole Mounting Assembly 

 

 

 

 

Содержание AirSpeed 1030 B48


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды