manualshive.com logo in svg

Airspan AirSpeed 1030 B48, Руководство по установке

Поделиться
Скачать
Airspan AirSpeed 1030 B48 Скачать руководство пользователя страница 28

 AirSpeed 1030 B48 Installation Guide 

DUG01623

 

Airspan Commercial and Internal Use 

26 

 

 

4.2 Connecting the GPS Antenna 

Note:

 The GPS Antenna Kit is ordered separately. 

 

Note:

 AirSpeed 1030 B48 works only with GPS antennas that are approved by Airspan. 

The following describes the connection of the GPS antenna which is installed directly to the top of the 
unit. 

1.  Unscrew the protective metal sealed cap from the GPS antenna jack prior to mounting the 

GPS on the AirSpeed-1030 B48 unit. 

2.  Align the GPS jack with the plug attached to the top panel on the unit. 

3.  Attach the GPS antenna to the TNC connector on the unit. 

 

Figure 7: Attaching GPS Antenna 

 

 

Caution:

 Take care not to over tighten so as not to damage the threads. 

 

Note:

 It is required to weather-proof all the antenna connections. This is done with a layer of self-

amalgamating  tape  followed  by  an  over  layer  of  PVC  tape.  See 

Weather-proofing  Antenna 

Connections

. 

 

Note:

 In the event no external GPS antenna is required (i.e. 

– when used for 1588 clock sync), leave 

the sealed cap in place and weather-proof the antenna connection, as described below. 

4.3 Weather-proofing Antenna Connections 

Note:

 The RF connectors on the Front Mount Antenna arrive pre-connected. Weather-proofing is 

best done at this stage to give easier access to the connections. 

Weather-proofing of the antenna connections is required. This is done with a layer of self-
amalgamating tape followed by an over layer of PVC tape. Verify the RF connector is completely 
weather-sealed. 

Содержание AirSpeed 1030 B48


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды