manualshive.com logo in svg

Airspan AirSpeed 1030 B48, Руководство по установке

Поделиться
Скачать
Airspan AirSpeed 1030 B48 Скачать руководство пользователя страница 33

 AirSpeed 1030 B48 Installation Guide 

DUG01623

 

Airspan Commercial and Internal Use 

31 

 

 

5  Connect and Manage Cables 

The following section explains the grounding procedure, cable preparation, external antenna 
assembly and general instructions on how to connect the DC power cable and the Fiber Ethernet 
(SFP) cable to the AirSpeed 1050 unit. 

Note:

 Grounding cable, Fiber cables, SFP connector adaptor and AC power cable. Ethernet cables 

and RJ45 copper connector adaptor are not supplied as part of the AirSpeed 1030 B48 and can be 
ordered separately. 

5.1 Grounding 

The AirSpeed 1030 B48 requires a secure ground connection and a grounding screw fitted with a flat 
washer and lock washer is provided on the back and clearly marked with the universal ground 
symbol. 

The cable (not supplied) should be grounded and bonded according to international or local 
standards. 

 

Figure 12: Ground Connection 

 

 

 

5.2 Fiber Ethernet (SFP) Cable Preparation 

Note:

 Additional parts required for the SFP assembly: 

 

LC Duplex cable assembly 

 

SFP Transceiver   

 

Note:

 To ensure proper operation, 

SFP’s that are approved by Airspan should be used. 

The following displays the proper steps for SFP cable preparation: 

1. 

Have the pre-assembled LC Duplex cable assembly ready.  

Note:

 Diameter of cable is in the 4.8 to 6.8mm (0.19

”-0.26”) range.  

 

Figure 13: Pre-assembled LC Duplex Cable 

 

 

Содержание AirSpeed 1030 B48


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды