manualshive.com logo in svg

Airspan AirSpeed 1030 B48, Руководство по установке

Поделиться
Скачать
Airspan AirSpeed 1030 B48 Скачать руководство пользователя страница 31

 AirSpeed 1030 B48 Installation Guide 

DUG01623

 

Airspan Commercial and Internal Use 

29 

 

 

4.5 Wall Mount Assembly 

The following describes the wall mounting procedure: 

1.  Select the location on the wall to mount the AirSpeed 1030 B48 mounting bracket.  

 

2.  Position the mounting (base) bracket onto the wall at the required height and mark where to 

drill the holes. 

3.  Insert screws and appropriate wall anchors (not provided) and tighten in place. 

4.  Assemble the 2 SEMS screws (M8 x 20) into the lower threaded holes on the mounting 

(base) bracket, do not tighten. 

Note:

 Wall plugs (x4) and necessary hardware are 

not

 supplied by Airspan and are the 

responsibility of the installer. Use appropriate wall plugs according to field conditions. 

 

5.  Carefully align and position the unit so that the screws (1 on each side) fit into the notched 

grooves provided on the back bracket (pre-assembled on the unit) and hand tighten. Insert 
the M8 screws, washers and nuts (supplied) and fasten the back bracket (pre-assembled on 
the unit) to the mounting bracket. 

6.  Adjust the unit so that the GPS is positioned upright. Check and tighten all fixing screws. 

(Tighten to a torque of no more than 12.5 Nm (9.22 ft-lb) max.) 

 

Figure 10: AirSpeed on Wall 

 

 

 

 

Содержание AirSpeed 1030 B48


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды