AirMan SDG60S-7A6 Скачать руководство пользователя | Manualshive

Страница: 39 / 61

background image

5. Periodic Inspection/Maintenance

5

-

2

5.2 Daily Inspection and Keeping Operation Log

Be sure to carry out daily inspection every morning before operation. See Chapter 4 “OPERATION”
of the manual for the details of inspection.

Pay attention to and carefully observe the following points during daily operation or inspection and
maintenance work. If any trouble or abnormality is found, immediately investigate its cause and
make repairs. If the cause is unknown or not traceable, or if the trouble involves a part or compo-
nent not described in the manual, ask your nearest dealer for information.

(a) Controls and instruments function properly.
(b) Quantity and any leak of water, fuel, and oil or

any contamination should be checked.

(c) Appearance, abnormal noise or excessive heat

should be checked.

(d) Loose bolt or nut should be checked.
(e) Any damage, wear or shortage of machine

components and parts should be checked.

(f) Performance of each part or component should

be proper

.

Keep the operation log to record constant inspection of each component, so that trouble of the ma-
chine can be easily discovered and preventive measures can be taken.
It is very useful to record information such as frequency, temperature, current, maintenance items
and replenishment of lubricant on a daily maintenance log.

5.3 Periodic Replacement of Parts

Air filter is a crucial component for the performance and the life of a unit.
Use genuine part for replacement.

Part number changes upon modification. For replacement of parts, make sure whether the part
number is correct or applicable.

Part Name

Part Number

Quantity

Engine oil filter

ISUZU 113240 2321

1

Air filter element

32143 12700

1

Fuel filter

ISUZU 113240 0791

1

Filter inside Fuel Air-bleeding

Electric Pump

ISUZU 894337 0220

1

V-belt

ISUZU 113671 3270

1

Fuel feed pump gasket

ISUZU 9-0957-2014-0

6

Sedimenter gasket

ISUZU 9-0957-2014-0

2

TR0049

Use our genuine elements

«
...
37
38
39
40
41
...
»

Содержание SDG60S-7A6






























































Отзывы:

Нет отзывов

Похожие инструкции для SDG60S-7A6

Бренд: GE Страницы: 120

Бренд: Data Translation Страницы: 64

Бренд: Data Translation Страницы: 84

Бренд: Data Translation Страницы: 54

Бренд: Data Translation Страницы: 54

AVerCaster HD Duet

Бренд: Avermedia Страницы: 4

SUNNY TRIPOWER STP 20000TL-30

Бренд: SMA Solar Technology Страницы: 50

Бренд: Canary Страницы: 3

OBID i-scan ID ISC.ANT.PS-A

Бренд: Feig Electronic Страницы: 28

exacqVision E Series

Бренд: Exacq Страницы: 70

Бренд: Plexim Страницы: 8

Бренд: Wisenet Страницы: 8

Бренд: FBS Страницы: 6

Бренд: KONANlabs Страницы: 6

CPSPI3700EVF380

Бренд: CyberPower Страницы: 94

Бренд: Niveo Страницы: 3

Бренд: Cobra Страницы: 12

Бренд: B meters Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды