background image

4. Operation

 

 

4

-

2

4.2  Protection device 
 

 

For prevention of troubles during operation, this machine is provided with various protection devices.   
When the engine stops due to function of the protection devices and circuit breaker trips, get rid of the 
causes of trouble, referring to the trouble shooting clause and then restart operation.

 

 

4.2.1  

List of protection devices

 

 

This machine is equipped with the following devices in the table. Repair and make necessary 

treatment in accordance with the item 

 

Item 

Engine 

stops

 

3 phase or 

single phase 

circuit 

breaker trips.

 

Lamp 

display 

Monitor 

Functions

 

Engine oil pressure 
drop 

 

 

 

 

When engine oil pressure drops, it 
functions. 
Operating pressure: lower than 
0.1MPa 

Engine water tem-
perature rises.

 

 

 

 

 

In case of abnormal rise of engine 
water temperature, it functions.

 

temperature reaches 105

 

Excessive rotation

 

 

 

 

 

When engine rotates excessively, 
it begins to function.

 

Function rotation: 2,070min

-1

 

(69Hz)

 

Clogging of air fil-
ter

 

 

 

 

 

When air filter is clogged and it 
becomes necessary to clean it, it 
functions.

 

 

Oil Fence 

 

 

 

 

When more condensate (fuel, en-
gine oil and coolant) than 1/3 of 
capacity in the oil fence is accu-
mulated monitor lamp lights. 

Discharged battery 

 

 

 

 

It functions in case of faulty bat-
tery. 

Overcurrent or 
short circuit 

 

 

 

 

In case of overload or short circuit 
accident, it functions. 

When the monitor lamp lights in the oil fence, immediately drain it. 

(For the capacity of the oil fence, refer to 8.1 Specifications).    To protect environment, do not drain it di-
rectly into rivers. (For details, see 4.6) 

 

Содержание SDG60S-7A6






























































Отзывы: