Aircel ABP Series Скачать руководство пользователя страница 41

Страница: 41 / 52

Blower Purge Desiccant Air Dryer

ABP Series

TROUBLESHOOTING TABLE

Problem

Probable Cause

Remedy

Vessel 2

Depressurization

Failure

The depressurization valve did not open

Check the purge exhaust solenoid valves for

correct operation. Check the valve actuator

for correct operation.

Vessel did not fully depressurize.

Check to determine if the depressurization muffler is

plugged. If so, replace.

Vessel depressurized, but alarm is on.

Check the pressure sensor for correct operation.

Vessel 1 Re-

pressurization Failure

( 5 minute timer to

alarm)

The re-pressurization valve did not open.

Check the re-pressurization solenoid valve for correct

operation. Check the valve actuator

for correct operation.

Vessel re-pressurized, but the

alarm is on.

Check pressure sensor for correct operation.

Vessel 2 Re-

pressurization Failure

( 5 minute timer to

alarm)

The re-pressurization valve did not open.

Check the re-pressurization solenoid valve for correct

operation. Check the valve actuator

for correct operation.

Vessel re-pressurized, but the

alarm is on.

Check pressure sensor for correct operation.

Regeneration

Heater Sheath Over

Temperature Failure

Defective or open circuit thermocouple.

Replace the thermocouple. RESET alarm.

Low or no regeneration blower flow.

Check the manual valve on the blower. Check the

blower, blower motor and overloads, and blower inlet

filter. Replace as necessary. Press RESET to restart.

Problem with PLC control system.

Replace as needed.

Failure of

Regeneration Outlet

Valves to Operate

Defective solenoid valve, loss of power or

loss of pilot air.

Check the solenoid valve operation and verify the

continuity of the solenoid coil. Replace as necessary.

Check the pilot air system and verify that pilot air is

present at the solenoid valves.

Defective valve actuator.

Verify that the valve actuator can be rotated by

hand with a wrench. If not, replace actuator.

Butterfly valve defective.

Verify that the valve shaft can be rotated by

hand with a wrench. If not, replace or rebuild valve.

Содержание ABP Series





















































Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды

Aircel ABP Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды