Aircel ABP Series Скачать руководство пользователя страница 10

Страница: 10 / 52

ABP Series |

Blower Purge Desiccant Air Dryer

System

The heated regenerative desiccant dryer is a continuous-

duty compressed air dryer used in industrial applications

to provide high drying efficiency for large volume airflows.

Continuous duty means no downtime. A switching valve

alternates the desiccant chambers between the drying and

regeneration phases. While one chamber is drying, the other

is regenerating.

The self-contained heated regenerative desiccant dryer

includes a control system, dryer, regeneration blower and

heater, and silencers.

The heated blower purge regenerative desiccant dryer

features high separation efficiency desiccant to ensure

high water removal rates. Control system include the PLC

electronic controller and the energy management system.

Both offer consistent reliable control and tremendous energy

savings. The standard EMS (Energy Management System)

allows for either fixed time or energy saving demand modes

of operation.

How It Works

1. Pre-filtered wet compressed air enters the bottom of the

on-line vessel.

2. Compressed air passes upward through the desiccant

bed; moisture is removed, lowering the dew point to

-40o F.

3. Dry compressed air exits the top of the vessel and flows

downstream to the after filter, monitored constantly via

standard dew point sensor. This EMS feature extends

the drying period until the target dew point occurs. This

greatly reducing energy costs.

4. Prior to regeneration, saturated on line vessel goes off-

line and depressurizes to ambient through an angle seat

valve & muffler.

5. After the off-line vessel has depressurized, a blower

draws in ambient air for regeneration.

6. The air passes through an immersion heater, check

valve, and enters top of regenerating vessel.

DESIGN PARAMETERS

DRYER DESCRIPTION

Type of dryer:

Desiccant

Power supply:

460 Volt / Three Phase / 60Hz

Desiccant type:

Premium Grade Activated Alumina

All Models

Parameter

Description

Air Pressure

Air Inlet

Temperature

Ambient

Temperature

Maximum

135 psig

120 (°F)

Minimum

60 psig

40 (°F)

38 (°F)

Содержание ABP Series





















































Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды

Aircel ABP Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды