Aircel ABP Series Скачать руководство пользователя страница 36

Страница: 36 / 52

ABP Series |

Blower Purge Desiccant Air Dryer

Heatless Mode Screen

HEATLESS MODE

Heatless Mode is an operation that can be utilized if any of the

following upset conditions should happen:

• Blower motor failure
• Heater failures

During these upset conditions, the unit will not be able to

function due to the failure of any one of the listed components

above. To keep the unit operating, Aircel has provided a

solution; Heatless Mode. In heatless mode, the unit will

regenerate each tower utilizing certain steps while locking out

others. The timing has been altered in the program to make

this functional. This will keep the unit running long enough to

replace the components without much downtime.

TO PLACE THE UNIT IN HEATLESS MODE:

Please follow the steps below to place the unit in heatless

mode.

Note:

The unit will not operate correctly if the

heatless mode button is pressed during any other step

than depressurization. Please follow the instructions below

properly.

• Turn unit off to ensure there is no power present

in the panel.

• Remove the heater fuses to ensure the heater

will not operate by accident.

• Once the fuses are removed and the panel is

locked, return power to the panel.

• After the startup period of 3 to 4 minutes, the

PLC will be ready to communicate with the HMI.

• Navigate to the service menu and select Activate

Service Mode.

• Once in service mode, return to the operations

screen and step through to the re-pressurization

step (6 or 12).

• Return to the service menu and Deactivate

Service Mode.

• Activate heatless mode by pressing the Heatless

Mode Off button.

• Navigate back to the Operations screen.

The unit should now be in heatless mode and switching

towers every 7.5 minutes. This will keep the unit running.

Please note that in heatless mode, the unit will be

using dry air from the outlet of the unit to purge the

regenerating vessel. This may cause a slight decrease in air

flow from the dryer.

To deactivate heatless mode (once the component has

been replaced), follow the steps below:

• Wait till the unit is in re-pressurization steps 6 or

12.

• Deactivate heatless mode by pressing the

heatless mode button in the service menu.

• The unit will now return to standard blower

purge mode.

• Turn the power off to the panel and replace the

heater fuses.

• Re-apply power and return to normal operations.

For more assistance, please contact a service technician by

calling the number provided on the back page of the user

manual.

AIRCEL PROGRAMMABLE CONTROLLER (APC)

Содержание ABP Series





















































Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды

Aircel ABP Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды