Aircel ABP Series Скачать руководство пользователя страница 19

Страница: 19 / 52

Blower Purge Desiccant Air Dryer

ABP Series

AIRCEL PROGRAMMABLE CONTROLLER (APC)

Control Menu Screen

The control menu allows the user some control over system operation, as well as the ability to navigate to the other status and

alarm screens. Red buttons indicate off while green buttons indicate on and yellow buttons indicate status screens.

Toggle Blower Cool

On/Off

Navigate to flow

diagram

Navigate to service

menu

Heatless Mode

Indicator

(note: not

visible in normal operation,

only in heatless mode)

Navigate to Dryer

Status Screen

Navigate to

Alarm Status

Screen

Navigate to

Alarm Log Screen

Navigate to

temperature

settings screen

Dry Cool Purge

Air On/Off

System On/Off

Dew Point

Demand On/Off

Navigate to

Normal Running

Screens

Service Mode

Indicator

(note:

not visible in normal

operation, only in

service mode)

Dry Cool Purge Air On/Off:

Button toggles dry cool purge on/

off. Green ON is dry air purge from system outlet for system

cooling. Red OFF is blower only cooling, which will give a high

dew point on switchover.

System On/Off:

Button toggles system on/off. Green ON is

system running. Red OFF is system not running.

Dew Point Demand On/Off:

Button toggles energy saving

mode on/off. Green ON enables energy saving mode. Red OFF

disables energy saving mode, enables fixed time cycle mode -

system cycles on a continuous cycle.

Blower Cool On/Off: Button toggles blower cool on/off.

Green ON draws in atmospheric pressure through the blower

in order to cool the heater sheath. Red OFF will turn both the

Dry Air Cooling and Blower Cool off.

WARNING: The unit will

not cool properly when turned off!

Running Screens:

Navigate to the normal running screens

Dryer Status:

Navigates to dryer status screen

Flow Diagram:

Navigates to the flow diagram screen

Service Menu:

Navigates to the service menu screen

Alarm Status:

Navigates to the alarm status screen

Alarm Log:

Navigates to the alarm log screen

Temp Settings:

Navigates to the temperature settings screen

NOTES:

Содержание ABP Series





















































Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды

Aircel ABP Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды