Aircel ABP Series Скачать руководство пользователя страница 26

Страница: 26 / 52

ABP Series |

Blower Purge Desiccant Air Dryer

AIRCEL PROGRAMMABLE CONTROLLER (APC)

Dryer Operations, Cont.

STEP NINE: Operation Screen

Vessel 2 is drying the inlet air (Vessel 2 inlet valve should

be open)…Vessel 1 has depressurized to 8 PSI preparing for

regeneration…solenoids SOL3, SOL5, SOL9 and SOL 12 energize

opening valves V3, V5, V9 and V12. Vessel 2 regeneration valves

V4, V6, V10, V11 and V13 along with Depressurization valve V8

and inlet valve V1 should be closed.
The screen will not be visible when the unit is in Service Mode

or Heatless Mode. If Service or Heatless Mode is activated

during this step, the unit will advance to the next step (Heatless

Mode) or the “Press to Proceed” button will appear (Service

Mode).
WARNING: If the screen is unlocked, the screen will not

advance nor will the “Press to Proceed” button appear when the

step is complete.

STEP TEN: Operation Screen

Vessel 2 is drying the inlet air (Vessel 2 inlet valve should be

open).
Vessel 1 is depressurized to 8 psi. Vessel 1 depressurization

valve V1 and regeneration valve K3 is open.
The blower and heater turn on and the heat regeneration

process now begins. The heating process cycle can operate

for up to a period of 172 minutes. If the regeneration outlet

temperature reaches 200°F during this cycle, the heater will

turn off (the blower will remain on) and the heating step

will terminate early saving additional energy. The PLC will

automatically advance to the heater cooling cycle.
If in service mode, the “Proceed to Next Step” will be displayed

on the screen once the Step is complete. If everything has been

verified in the step, press the “Proceed” button to proceed to

next step. This will allow an authorized service technician to

view operation of the system in a shorter time period.
WARNING: If the screen is unlocked, the screen will not

advance nor will the “Press to Proceed” button appear when the

step is complete.

This screen displays the temperature of the heater sheath,

heater outlet, and regeneration outlet, as well as the heat

regeneration time.

Note:

The “Service Mode Press to Proceed to Next Step”

button in red is a service fast cycle button to allow an

authorized technician to advance to the next step without

waiting for the step to finish.
WARNING: this button should not be operated unless

authorized by an Aircel Service technician and the valving

and operation is verified.

Содержание ABP Series





















































Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды

Aircel ABP Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание ABP Series

Отзывы:

Похожие инструкции для ABP Series

Бренды по названию

Популярные бренды