Air Live WN-350R Скачать руководство пользователя страница 65

Страница: 65 / 176

2. System and Network Setup

WN-350R User’s Manual

MTU (5):

Please input the MTU value of your network connection

here. If you don’t know, you can use default value.

BEZEQ-ISRAEL (6): If you are connecting to the BEZEQ network in Israel.

Please enable this function.

Connection type (7): Please select the connection type of Internetconnection

you wish to use, please refer to section 2-5-3 for

detailed descriptions.

Idle Time Out (8):

Please input the idle time out of Internet connection you

wish to use, and refer to section 2-5-3 for detailed

descriptions.

When you finish with all settings, please click ‘Apply’ (9) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take

effect (Please wait for about 30 seconds while router is rebooting).

If you want to reset all settings in this page back to previously-saved value,

please click ‘Cancel’ button.

Содержание WN-350R

















































































































































































Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды

Air Live WN-350R, Руководство пользователя

Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды