Air Live WN-350R Скачать руководство пользователя страница 62

Страница: 62 / 176

2. System and Network Setup

WN-350R User’s Manual

Connection Type (5): Please select the connection type of Internet

connection you wish to use.

Continuous – The connection will be kept always on. If the

connection is interrupted, the router will re-connect

automatically.

Connect On-Demand – Only connect when you want to

surf the Internet. “Idle Time Out” is set to stop the

connection when the network traffic is not sending or

receiving after an idle time.

Manual – After you have selected this option, you will see

the “Connect” button and “Disconnect” button, click

“’Connect” and the router will connect to the ISP. If you

want to stop the connection, please click “Disconnect”

button.

Idle Time Out (6):

If you have selected the connection type to

“Connect-On-Demand”, please input the idle time out.

After you finish with all settings, please click ‘Apply’ (7) button and the following

message will be displayed on your web browser:

Please click ‘Continue’ to back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take

effect (Please wait for about 30 seconds while router is rebooting).

Содержание WN-350R

















































































































































































Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды

Air Live WN-350R, Руководство пользователя

Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды