Air Live WN-350R Скачать руководство пользователя страница 42

Страница: 42 / 176

2. System and Network Setup

WN-350R User’s Manual

BEZEQ-ISRAEL (6): Setting item ‘BEZEQ-ISRAEL’ is only required to check

if you’re using the service provided by BEZEQ network

in Israel.

Connection type (7): Please select the connection type of Internet

connection you wish to use, please refer to last section

for detailed descriptions.

Idle Time Out (8):

Please input the idle time out of Internet connection you

wish to use, and refer to last section for detailed

descriptions.

When you finish with all settings, please click ‘OK (9); if you want to go back to

previous menu, click ‘Back’.

2.3.5. Setup Procedure for ‘L2TP xDSL’

L2TP is another popular connection method for xDSL and other Internet

connection types, and all required setting items are the same with PPTP

connection.

Like PPTP, there are two kinds of required setting, we’ll start from ‘WAN

Interface Settings’:

Содержание WN-350R

















































































































































































Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды

Air Live WN-350R, Руководство пользователя

Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды