Air Live WN-350R Скачать руководство пользователя страница 163

Страница: 163 / 176

3. Advanced Functions

WN-350R User’s Manual

154

Here are descriptions of every buttons:

Backup

Press ‘Save’ button, and you’ll be prompted to

Settings (1):

download the configuration as a file, default filename is

‘config.bin’, you can save it as another filename for

different versions, and keep it in a safe place.

Restore

Press ‘Browse…’ to pick a previously-saved

Settings (2):

configuration file from your computer, and then click

‘Upload’ to transfer the configuration file to router. After

the configuration is uploaded, the router’s configuration

will be replaced by the file you just uploaded.

Restore to

Click this button to remove all settings

Factory Default (3):

you made, and restore the configuration of this router

back to factory default settings.

Содержание WN-350R

















































































































































































Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды

Air Live WN-350R, Руководство пользователя

Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды