background image

  3.  Advanced Functions 

119                     

WN-350R User’s Manual

 

 

Here are descriptions of every setup items: 

Enable Virtual   

 Check this box to enable virtual server, and uncheck 

Server (1):   

 this box to disable virtual server. 

Private IP (2):   

 Input the IP address of the computer which provides 

Internet service. 

Computer Name (3):  Pull down the menu and all the computers connected to 

the router will be listed here. You can easily to select the 

computer name without checking the IP address of the 

computer. 

Private Port (4):   

Input the port number of the IP address which provides 

Internet service. 

Type (5):   

 Select the type of connection, TCP or UDP. If you’re not 

sure, please select ‘Both’. 

Public Port (6):   

Please select the port number of Internet IP address 

which will be redirected to the port number of local IP 

address defined above. 

Comment (7):   

 Please input any text to describe this mapping, up to 16 

alphanumerical characters. 

Add (8):   

 Add the mapping to virtual server table. 

Reset (9): 

 Remove all inputted values. 

Virtual Server   

 All existing virtual server mappings will be displayed 

Table (10):   

 here. 

Содержание WN-350R

















































































































































































Отзывы: