Air Live WN-350R Скачать руководство пользователя страница 174

Страница: 174 / 176

4. Appendix

165

WN-350R User’s Manual

ISP Gateway Address:

(see ISP for definition). The ISP Gateway Address is

an IP address for the Internet router located at the ISP's office.

ISP:

Internet Service Provider. An ISP is a business that provides connectivity

to the Internet for individuals and other businesses or organizations.

LAN:

Local Area Network. A LAN is a group of computers and devices

connected together in a relatively small area (such as a house or an office).

Your home network is considered a LAN.

MAC Address:

MAC stands for Media Access Control. A MAC address is the

hardware address of a device connected to a network. The MAC address is a

unique identifier for a device with an Ethernet interface. It is comprised of two

parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each

manufacturer), plus 3 bytes that are often used as the product’s serial number.

NAT:

Network Address Translation. This process allows all of the computers

on your home network to use one IP address. Using the broadband router’s

NAT capability, you can access the Internet from any computer on your home

network without having to purchase more IP addresses from your ISP.

Port:

Network Clients (LAN PC) uses port numbers to distinguish one network

application/protocol over another. Below is a list of common applications and

protocol/port numbers:

Application

Protocol Port Number

Telnet

TCP

FTP

TCP

SMTP

TCP

POP3

TCP

110

H.323

TCP

1720

SNMP

UCP

161

SNMP Trap

UDP

162

HTTP

TCP

PPTP

TCP

1723

PC Anywhere TCP

5631

PC Anywhere UDP

5632

Содержание WN-350R

















































































































































































Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды

Air Live WN-350R, Руководство пользователя

Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды