Air Live WN-350R Скачать руководство пользователя страница 172

Страница: 172 / 176

4. Appendix

163

WN-350R User’s Manual

4.3. Glossary

Default Gateway (Router):

Every non-router IP device needs to configure a

default gateway’s IP address. When the device sends out an IP packet, if the

destination is not on the same network, the device has to send the packet to its

default gateway, which will then send it out towards the destination.

DHCP:

Dynamic Host Configuration Protocol. This protocol automatically

gives every computer on your home network an IP address.

DNS Server IP Address:

DNS stands for Domain Name System, which allows

Internet servers to have a domain name (such as www.Broadbandrouter.com)

and one or more IP addresses (such as 192.34.45.8). A DNS server keeps a

database of Internet servers and their respective domain names and IP

addresses, so that when a domain name is requested (as in typing

"Broadbandrouter.com" into your Internet browser), the user is sent to the

proper IP address. The DNS server IP address used by the computers on your

home network is the location of the DNS server your ISP has assigned to you.

DSL Modem:

DSL stands for Digital Subscriber Line. A DSL modem uses your

existing phone lines to transmit data at high speeds.

Ethernet:

A standard for computer networks. Ethernet networks are connected

by special cables and hubs, and move data around at up to 10/100 million bits

per second (Mbps).

Idle Timeout:

Idle Timeout is designed so that after there is no traffic to the

Internet for a pre-configured amount of time, the connection will automatically

be disconnected.

Содержание WN-350R

















































































































































































Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды

Air Live WN-350R, Руководство пользователя

Результаты поиска

Содержание WN-350R

Отзывы:

Похожие инструкции для WN-350R

Бренды по названию

Популярные бренды