Agilent Technologies 53210A Скачать руководство пользователя | Manualshive

Страница: 35 / 44

background image

53210A/53220A/53230A Option Installation

35

53210A/53220A/53230A Option Installation

neously

press in the right side panel of the aluminum chassis until the front panel

is partially released.

9. Using gentle pressure on both sides of the front panel, push the front

panel away from the motherboard to release the edge connector and free

the front panel completely.

10. Insert the typeN- to- SMA connector- adapter into the Channel 3 hole on

the front panel (remove the hole- plug, if necessary), so that the typeN

connector is on the front side of the front panel.

11. On the back side of the connector- adapter, place the washer plate and

the 14mm hex nut over the SMA connector and secure. See Figure 21.

N O T E

At this point, the front panel is only held to the A1 motherboard by an edge con-
nector.

N O T E

Make sure the word "LIFT" is visible on the washer-plate and that the "LIFT" tab
on the washer-plate is not underneath the hex nut.

«
...
33
34
35
36
37
...
»

Содержание 53210A













































Отзывы:

Нет отзывов

Похожие инструкции для 53210A

Бренд: Sanyo Страницы: 5

Бренд: Sanyo Страницы: 52

Бренд: Sanyo Страницы: 72

Бренд: Sam4s Страницы: 132

Бренд: Sam4s Страницы: 241

Бренд: Nautilus Страницы: 182

Бренд: Olympia Страницы: 38

COUNT-100-DELUXE-US

Бренд: Labelmate Страницы: 2

Бренд: Labelmate Страницы: 61

Бренд: Olympia Страницы: 10

Бренд: Hameg Страницы: 36

AB-1100 Plus UV

Бренд: AccuBANKER Страницы: 31

Бренд: Veeder-Root Страницы: 4

Бренд: GBA Страницы: 33

Бренд: TEC Страницы: 104

POS ColorTouch 64 Bit

Бренд: Vectron Страницы: 368

Бренд: Sam4s Страницы: 3

Бренд: Casio Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды