Agilent Technologies 53210A Скачать руководство пользователя | Manualshive

Страница: 22 / 44

background image

22

53210A/53220A/53230A

Option

Installation

53210A/53220A/53230A Option Installation

9. Using gentle pressure on both sides of the front panel, push the front

panel away from the motherboard to release the edge connector and free

the front panel completely.

10. Insert the typeN- to- SMA connector- adapter into the Channel 2 hole on

the front panel (remove the hole- plug, if necessary), so that the typeN

connector is on the front side of the front panel.

11. On the back side of the connector- adapter, place the washer plate and

the 14mm hex nut over the SMA connector and secure. See Figure 13.

Figure 13. Connector-Adapter Installation.

12. Pull up slightly on the "LIFT" tab on the washer- plate so that the tab

blocks the hex nut from coming unscrewed after installation.

N O T E

At this point, the front panel is only held to the A1 motherboard by an edge con-
nector.

N O T E

Make sure the word "LIFT" is visible on the washer-plate and that the "LIFT" tab
on the washer-plate is not underneath the hex nut.

«
...
20
21
22
23
24
...
»

Содержание 53210A













































Отзывы:

Нет отзывов

Похожие инструкции для 53210A

Бренд: Magnescale Страницы: 338

Бренд: Sam4s Страницы: 68

Бренд: Sam4s Страницы: 88

Invitrogen Countess II FL

Бренд: Thermo Scientific Страницы: 82

Бренд: Sam4s Страницы: 271

Бренд: Hitachi Страницы: 66

Бренд: Hitachi Страницы: 92

Бренд: Royal Страницы: 125

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 132

Бренд: AlphaLab Страницы: 7

Бренд: Labelmate Страницы: 75

Бренд: Olympia Страницы: 10

Бренд: Xiamen Страницы: 37

Бренд: Optimas Страницы: 6

Бренд: Rockwell Automation Страницы: 28

Бренд: DIEBOLD NIXDORF Страницы: 51

Бренд: Sam4s Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды