manualshive.com logo in svg

Agilent Technologies 53210A, Опции установки

Поделиться
Скачать
Agilent Technologies 53210A Скачать руководство пользователя страница 19

53210A/53220A/53230A Option Installation

19

53210A/53220A/53230A Option Installation

Figure 10. 53210A Channel 2 Front Panel Option 106/202.

Channel 2 Front Panel Installation Procedure (53210A) 

1. Remove the front panel assembly as follows:

2. Turn the chassis upside down. On the bottom of the motherboard, 

remove the T10 TORX screw that secures the smaller P500 Processor 

board to the motherboard (see Figure 11; for illustration purposes only, 

the P500 board is shown with plastic support bracket removed).

Figure 11. P500 Processor Board.

 

N O T E

Read each instruction step in its entirety, while examining the hardware and refer-
ring to the appropriate figure(s), before proceeding with the step. This will 
acquaint you completely, in advance, with the action to be performed. The actions 
in some steps must be accomplished simultaneously to succeed. Read all nearby 
NOTES carefully.

Содержание 53210A













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды