Agilent Technologies 53210A Скачать руководство пользователя страница 9

Страница: 9 / 44

53210A/53220A/53230A Option Installation

Internal Battery DC Power (Option 300)

Option 300 Battery Pack Parts (53200U - 300)

Item

Agilent Part No.

Qty.

•

Battery charger PCB Assembly

53200-66507

•

Battery

1420-0909

•

Y-Cable

53200-61602

•

Ribbon cable, 6-pin

53200-61603

•

Deck

53200-00601

•

Cover

53200-00602

•

TORX 10 screws

0515-0430

•

TORX 20 screws

0515-0433

Preliminary Steps

1. Remove the cover and rear bezel as described under “

Removing the

Cover and Rear Bezel

” at the beginning of this document.

Procedure

1. Using a medium slot- head screwdriver, gently push back the 4- pin con-

nector lock tab on the motherboard end of the jumper cable that connects

between the Motherboard (J1000) and the PowerSupply board (J2). Refer

to Figures 4 and 5.

C A U T I O N

Before proceeding with the installation, follow all the ESD steps as outlined in the
section titled "Do This First"at the beginning of this document.

Содержание 53210A













































Результаты поиска

Содержание 53210A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 53210A, Опции установки

Результаты поиска

Содержание 53210A

Отзывы:

Бренды по названию

Популярные бренды