Agilent Technologies 4072A Advanced Скачать руководство пользователя страница 79

Страница: 79 / 84

Appendix A

Agilent 4072/4073 Preinstallation Guide, Edition 4

Confirming the System Power Safety

Confirming PDU and EMO Operation

4. Check the emergency breaker, disconnect device, LINE indicator, system switch, and controller power outlets

as follows:

a. Set the power board breaker to the

on position

b. Set the emergency breaker to the

on position

c. Rotate the door lock release screw counterclockwise, and then set the disconnect device to the

on position

(pozidrive screwdriver)

d. Confirm if the over voltage LED turns on. If so, check the source power line.

e. Confirm that the LINE indicator on the EMO panel turns on.

Press the system switch, and confirm that the green LED in the system switch turns on.

NOTE

Do steps c through f within 20 seconds. After 20 seconds, the cabinet fan error LED turns on. To
recover this, set the disconnect device to the

off position

and repeat steps c through f.

g. Confirm that the proper voltage is applied to the controller power outlets, using a hand-held multimeter.

h. Confirm that no voltage is being applied to the instrument power outlets.

Confirm that no voltage is being applied to the DVM and CMU power outlets.

5. Check the INSTRUMENT POWER ON/OFF switches, instrument power outlets, DVM and CMU power

outlets, and power outlet protector as follows:

a. Press the INSTRUMENT POWER ON switch on the EMO panel.

b. Confirm that the green LED in the INSTRUMENT POWER ON switch turns on.

c. Confirm that the proper voltage is applied to the instrument power outlets using a hand-held multimeter.

d. Confirm that the proper voltage is applied to the DVM and CMU power outlets using a hand-held

multimeter.

e. Press the power outlet protector to set it to the

out position

Confirm that no voltage is applied to the instrument power outlets.

g. Confirm that no voltage is applied to the DVM and CMU power outlets.

h. Press the power outlet protector to set it to the

in position

Press the INSTRUMENT POWER OFF switch on the EMO panel.

Confirm that the green LED in the INSTRUMENT POWER ON switch turns off.

k. Confirm that no voltage is applied to the instrument power outlets.

Confirm that no voltage is applied to the DVM and CMU power outlets.

m. Press the INSTRUMENT POWER ON switch.

Содержание 4072A Advanced





















































































Результаты поиска

Содержание 4072A Advanced

Отзывы:

Похожие инструкции для 4072A Advanced

Бренды по названию

Популярные бренды

Agilent Technologies 4072A Advanced, Руководство по предварительной установке

Результаты поиска

Содержание 4072A Advanced

Отзывы:

Похожие инструкции для 4072A Advanced

Бренды по названию

Популярные бренды