Agilent Technologies 4072A Advanced Скачать руководство пользователя страница 73

Страница: 73 / 84

Appendix A

Agilent 4072/4073 Preinstallation Guide, Edition 4

Confirming the System Power Safety

Connecting Site Power Line

WARNING

Main power cable connection must be performed by qualified personnel at the customer site.
Incorrect installation will result in serious injury to operating personnel and damage to the
equipment.

NOTE

•

See “Main power cable” for main power cable specification.

•

When to connect the power cable to the power distribution unit (PDU), ensure that it is
connected to the 30 A service.

Use the following procedure to connect the power distribution unit (PDU) to the site power line (source).

1. Set the switchboard breaker to OFF.

2. Open the system cabinet rear door with the key

provided.

3. Set the disconnect device and emergency breaker

to OFF.

4. Remove the PDU side cover.

disconnect
device

emergency
breaker

PDU side cover

Содержание 4072A Advanced





















































































Результаты поиска

Содержание 4072A Advanced

Отзывы:

Похожие инструкции для 4072A Advanced

Бренды по названию

Популярные бренды

Agilent Technologies 4072A Advanced, Руководство по предварительной установке

Результаты поиска

Содержание 4072A Advanced

Отзывы:

Похожие инструкции для 4072A Advanced

Бренды по названию

Популярные бренды