Agilent Technologies 4072A Advanced Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 84

background image

38

Chapter 2

Agilent 4072/4073 Preinstallation Guide, Edition 4

Site Preparation

Emergency Off (EMO) System

•

Turning on system instrument

Switching on the main breaker, the emergency breaker, and the main switch turns on the LINE indicator
(white), but the main contactor switch does not close. Figure 2-18 through Figure 2-20 show this condition.
When the system switch closes, power is supplied to the system controller. When the EMO panel
INSTRUMENT POWER ON switch closes, the coil of the main contactor is activated and the main contactor
switch closes. The INSTRUMENT POWER ON indicator (green) also turns on. Power is then supplied to the
system instruments.

•

Turning off system instrument

Pressing the EMO panel INSTRUMENT POWER OFF switch stops the current through the coil of the main
contactor, so the main contactor opens. This stops power to the system instruments.

•

EMO switch

When the EMO switch is pressed and its contacts open, the current through the coil of the main contactor stops
and the main contactor opens. The emergency breaker contacts also open. This stops power to both the system
instruments and system controller.

At the same time, the current through the coil of Relay2 flows, so one contact opens and the other contact
closes in Relay2. The Ext alarm 1, which is normally in the closed state, is opened, and the Ext alarm 2, which
is normally in the open state, is closed.

Opening the Ext control terminal is the same as pressing the EMO switch, which stops current through the coil
of Relay2, so one contact opens and the other closes. The current through the coil of the main contactor then
stops, the main contactor opens, and power to the system instruments stops. This also stops power to the system
controller.

Table 2-6 describes conditions for normal operation.

Table 2-6

Conditions for normal operation

Operation

Results

Power for

system

instruments

Ext. alarm 1

(NC)

a

a. NC (“Normally Closed”) indicates that the terminals are closed when the tester operates properly.

Ext. alarm 2

(NO)

b

b. NO (“Normally Open”) indicates that the terminals are open when the tester operates properly.

Disconnect device is ON

not supply

Open

Close

Pressing system switch

Close

Open

Pressing INSTRUMENT POWER ON switch

supply

pressing INSTRUMENT POWER OFF switch

Stop

Pressing EMO switch

Open

Close

Opening Ext. control

«
...
36
37
38
39
40
...
»

Содержание 4072A Advanced





















































































Отзывы:

Нет отзывов

Похожие инструкции для 4072A Advanced

Бренд: SAMCHULLY Страницы: 48

Бренд: Gallagher Страницы: 6

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

Бренд: Vari Lite Страницы: 14

Бренд: Vaniman Страницы: 3

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: Ultrasport Страницы: 72

Бренд: Wieland Страницы: 2

41370 Micro Spot

Бренд: SHOWTEC Страницы: 22

Бренд: Carestream Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды