Agilent Technologies 4072A Advanced Скачать руководство пользователя страница 28

Страница: 28 / 84

Chapter 2

Agilent 4072/4073 Preinstallation Guide, Edition 4

Site Preparation

Environmental Considerations

To ensure optimum 4072/4073 tester accuracy and performance, be sure to comply with the following
environmental conditions.

Temperature and humidity

The measurement accuracy is specified at the following temperature and humidity:

Temperature:

23 °C ± 5 °C (73 °F ± 9 °F)

Humidity:

5% to 70% RH (The 4073A/4072B/4073B must be free of condensing.)

NOTE

After the SMU calibration, the temperature change must be less than 3 °C.

In addition to the above temperature and humidity conditions, Agilent Technologies recommends
that the following conditions be satisfied for measuring low-current and low-voltage with the
4073A/B:

Temperature change:

Within ± 1 °C after the calibration

Temperature change period:

≥

10 minutes

Humidity:

≤

50%

The 4072/4073 must be operated under the following conditions:

For the 4072A:

Operating temperature:

5 °C to 40 °C (41 °F to 104 °F)

Storage temperature:

−

20 °C to 60 °C (

−

4 °F to 140 °F)

For the 4073A:

Operating temperature:

5 °C to 35 °C (41 °F to 95 °F)

Storage temperature:

−

20 °C to 50 °C (

−

4 °F to 122 °F)

Storage humidity:

≤

80%

For the 4072B/4073B:

Operating temperature:

5 °C to 30 °C (41 °F to 86 °F)

Storage temperature:

−

20 °C to 50 °C (

−

4 °F to 122 °F)

Storage humidity:

≤

80%

NOTE

When using the flat panel display with the 4072/4073, the following conditions must be satisfied,
in addition to the conditions shown above.

Operating humidity:

20% to 70% RH (no-condensing)

Storage humidity range:

20% to 85% (

−

20 °C to 50 °C,

−

4 °F to 122 °F)

20% to 55% (50 °C to 60 °C, 122 °F to 140 °F)

Содержание 4072A Advanced





















































































Результаты поиска

Содержание 4072A Advanced

Отзывы:

Похожие инструкции для 4072A Advanced

Бренды по названию

Популярные бренды

Agilent Technologies 4072A Advanced, Руководство по предварительной установке

Результаты поиска

Содержание 4072A Advanced

Отзывы:

Похожие инструкции для 4072A Advanced

Бренды по названию

Популярные бренды