background image

6

31025 R0

2

2.. S

Sa

affe

etty

y

2.1. Safety Alert Symbol and Signal Words

This safety alert symbol indicates important safety messages in this manual. When you see
this symbol, be alert to the possibility of injury or death, carefully read the message that
follows, and inform others.

Signal Words:

Note the use of the signal words

DANGER

,

WARNING

,

CAUTION

, and

NOTICE

with the safety

messages. The appropriate signal word for each message has been selected using the definitions below as a
guideline.

Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or
death.
Indicates a hazardous situation that, if not avoided, could result in serious injury or death.

Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided, may result in property damage.

2.2. General Safety

The safety information in the safety section of this manual applies to all safety practices. Specific safety
information (such as Operation Safety), can be found in the appropriate section.

YOU

are responsible for the

SAFE

use and maintenance of your X-Tend hopper.

YOU

must ensure that you and

anyone else who is going to work around the X-Tend hopper understands all procedures and related

SAFETY

information contained in this manual.

Remember,

YOU

are the key to safety. Good safety practices not only protect you, but also the people around

you. Make these practices a working part of your safety program. All accidents can be avoided.

• It is the X-Tend hopper owner, operator, and maintenance personnel's responsibility

to read and understand

ALL

safety instructions, safety decals, and manuals and

follow them when assembling, operating, or maintaining the equipment.

• Owners must give instructions and review the information initially and annually with all personnel before

allowing them to operate the X-Tend hopper. Untrained users/operators expose themselves and bystanders
to possible serious injury or death.

• The X-Tend hopper is not intended to be used by children.

• Use the X-Tend hopper for its intended purposes only.

• Do not modify the X-Tend hopper in any way without written permission from the manufacturer.

Unauthorized modification may impair the function and/or safety, and could affect the life of the X-Tend
hopper. Any unauthorized modification of the X-Tend hopper will void the warranty.

2. SAFETY

X-TEND HOPPER – X130

Содержание WHEATHEART X130















































Отзывы: