Afag 50315434 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 66

background image

16

– 66

Operating instructions EN

◼

SE-24

◼

01.06.2022

◼

V1.5

Avoiding accidents, bodily injuries and/or damage to property:

CAUTION

Additionally secure vertical axes against dropping or lowering after
switching off the motor, such as by:

▪

mechanical interlocking of the vertical axis,

▪

external braking/ catching/ clamping device or

▪

sufficient weight balancing of the axis.

The motor brake installed or an external motor brake controlled by
the drive control unit alone is not suitable for personnel safety!

CAUTION

Render the electrical equipment free of voltage via the main switch
and secure it against being switched on again, wait until the
intermediate circuit has been discharged during:

▪

maintenance work and repairs

▪

cleaning work

▪

long operational downtimes

Before carrying out any maintenance work, it must be ensured that
the power supply has been switched off, locked and that the
intermediate circuit has been discharged.

NOTE

It must also be ensured that the external voltage supply of the
controller (24 V) is switched off.

NOTE

The  intermediate  circuit  or  the  mains  voltage  must  always  be
switched  off  before  the  24V  voltage  supply  of  the  controller  is
switched off.

«
...
14
15
16
17
18
...
»

Содержание 50315434



































































Отзывы:

Нет отзывов

Похожие инструкции для 50315434

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Vaillant Страницы: 32

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 40

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренд: OJ Electronics Страницы: 8

Бренд: ACL Страницы: 20

SmarTemp Control fx

Бренд: Webasto Страницы: 8

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренд: Partlow Страницы: 49

Бренд: Ascon tecnologic Страницы: 11

Бренд: ROBOT3T Страницы: 21

Бренд: StudioComm Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды