Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 114

background image

Installation and Configuration

Ndrive HPe 50/75/100

2.3.1.2. Unpowered Motor and Feedback Phasing

Disconnect the motor from the controller and connect the motor in the test configuration shown in

.

This method will require a two-channel oscilloscope, a 5V power supply, and six resistors (10,000 ohm, 1/4
watt). All measurements should be made with the probe common of each channel of the oscilloscope
connected to a neutral reference test point (TP4, shown in

). Wave forms are shown while moving

the motor in the positive direction.

Figure 2-6:

Motor Phasing Oscilloscope Example

With the designations of the motor and Hall leads of a third party motor determined, the motor can now be
connected to an Aerotech system. Connect motor lead A to motor connector A, motor lead B to motor
connector B, and motor lead C to motor connector C. Hall leads should also be connected to their respective
feedback connector pins (Hall A lead to the Hall A feedback pin, Hall B to Hall B, and Hall C to Hall C). The
motor is correctly phased when the Hall states align with the Back EMF as shown in (

). Use the

CommutationOffset parameter to correct for Hall signal misalignment.

Figure 2-7:

Brushless Motor Phasing Goal

www.aerotech.com

Chapter 2

33

«
...
31
32
33
34
35
...
»

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ndrive HPe 100

Бренд: Raymarine Страницы: 23

encoTRive MD-025-CO-C Series

Бренд: TR-Electronic Страницы: 260

MASTERFLEX L/S 7523-40

Бренд: Cole Parmer Страницы: 23

Бренд: Danfoss Страницы: 2

Бренд: FujiFilm Страницы: 252

Бренд: Becker Страницы: 28

Бренд: ICAN Страницы: 14

SubDrive Inline 1100

Бренд: Franklin Electric Страницы: 13

Transmate 371-00

Бренд: Romac Страницы: 4

Бренд: E-Z Anchor Puller Страницы: 19

Бренд: Danfoss Страницы: 134

Бренд: Zest Страницы: 29

Slim Line External PC Card CD-ROM

Бренд: Targus Страницы: 22

Бренд: Wavelength Electronics Страницы: 23

VLT PTC Thermistor Card MCB 112

Бренд: Danfoss Страницы: 34

Classic Q3 15-150A 4 Quadrant

Бренд: Unitek Страницы: 35

Бренд: GE Страницы: 88

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды