Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 114

background image

Ndrive HPe 50/75/100

Accessories

5.1. Joystick Interface

Aerotech joysticks JI (NEMA12 (IP54) rated) and JBV are powered from 5V and have a nominal 2.5V output
in the center detent position. Three buttons are used to select axis pairs and speed ranges. An optional
interlock signal is used to indicate to the controller that the joystick is present. Joystick control will not
activate unless the joystick is in the center location. Third party devices can be used provided they produce
a symmetric output voltage within the range of -10V to +10V.

The following drawings illustrate how to connect a single- or two-axis joystick . For cable details refer to

. Refer to the A3200 Help file for programming information about how to change joystick

parameters.

Figure 5-1:

Single Axis Joystick Interface (to Aux I/O)

Figure 5-2:

Two Axis Joystick Interface (to the Aux I/O of two drives)

98

Chapter 5

www.aerotech.com

«
...
96
97
98
99
100
...
»

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ndrive HPe 100

Бренд: Onyx Страницы: 2

Бренд: Eaton Страницы: 208

Бренд: Tridonic Страницы: 14

Бренд: Leadshine Страницы: 33

Бренд: Leadshine Technology Страницы: 13

Бренд: LSIS Страницы: 81

Бренд: ANCA Motion Страницы: 170

Бренд: YASKAWA Страницы: 502

BLD-YT08D Series

Бренд: superbrightleds Страницы: 3

Бренд: Astraada Страницы: 82

Бренд: ZIEHL-ABEGG Страницы: 204

Emergency Lighting Si-36

Бренд: Assurance Engineering Страницы: 4

Бренд: YASKAWA Страницы: 71

Бренд: EasyDrive Страницы: 137

Бренд: ZIEHL-ABEGG Страницы: 204

Бренд: GFA Страницы: 17

Бренд: GFA Страницы: 28

Бренд: Danfoss Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды