Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 44

Страница: 44 / 114

Chapter 2

www.aerotech.com

2.4.1.4. Encoder Phasing

Incorrect encoder polarity will cause the system to fault when enabled or when a move command is issued.

illustrates the proper encoder phasing for clockwise motor rotation (or positive forcer movement

for linear motors). To verify, move the motor by hand in the CW (positive) direction while observing the
position of the encoder in the diagnostics display (see

Figure 2-17

). The Motor Phasing Calculator in the

Configuration Manager can be used to determine proper encoder polarity.

For dual loop systems, the velocity feedback encoder is displayed in the diagnostic display (

Figure 2-17

Figure 2-16:

Encoder Phasing Reference Diagram (Standard)

N O T E :

Encoder manufacturers may refer to the encoder signals as A, B, and Z. The proper phase rela-

tionship between signals is shown in

Figure 2-16

Ndrive HPe 50/75/100

Installation and Configuration

Содержание Ndrive HPe 100



















































































































Результаты поиска

Содержание Ndrive HPe 100

Отзывы:

Похожие инструкции для Ndrive HPe 100

Бренды по названию

Популярные бренды

Aerotech Ndrive HPe 100, Руководство по оборудованию

Результаты поиска

Содержание Ndrive HPe 100

Отзывы:

Похожие инструкции для Ndrive HPe 100

Бренды по названию

Популярные бренды