Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 114

background image

Installation and Configuration

Ndrive HPe 50/75/100

2.3.2.1. DC Brush Motor Phasing

A properly phased motor means that the positive motor lead should be connected to the ØA motor terminal
and the negative motor lead should be connected to the ØC motor terminal. To determine if the motor is
properly phased, connect a voltmeter to the motor leads of an un-powered motor:

1. Connect the positive lead of the voltmeter to the one of the motor terminals.

2. Connect the negative lead of the voltmeter to the other motor terminal.

3. Rotate the motor clockwise by hand.

Figure 2-9:

Clockwise Motor Rotation

4. If the voltmeter indicates a negative value, swap the motor leads and rotate the motor (CW, by hand)

again. When the voltmeter indicates a positive value, the motor leads have been identified.

5. Connect the motor lead from the voltmeter to the ØA motor terminal on the Ndrive HPe 50/75/100.

Connect the motor lead from the negative lead of the voltmeter to the ØC motor terminal on the Ndrive
HPe 50/75/100.

N O T E :

If using standard Aerotech motors and cables, motor and encoder connection adjustments are

not required.

www.aerotech.com

Chapter 2

35

«
...
33
34
35
36
37
...
»

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ndrive HPe 100

Бренд: Camozzi Страницы: 12

Бренд: Secure Data Страницы: 29

Бренд: Eaton Страницы: 14

Бренд: Fagor Страницы: 82

Бренд: Xinje Страницы: 189

CompletePower Plus CPP-A12V80A-SA-USB

Бренд: ElectroCraft Страницы: 42

ZAdyn4CA 018 HY

Бренд: ZIEHL-ABEGG Страницы: 28

Бренд: Küenle Страницы: 56

Бренд: Danaher Motion Страницы: 112

Бренд: easydriver Страницы: 68

Бренд: GU Страницы: 14

Бренд: Minarik Страницы: 56

Бренд: Philips Страницы: 177

Бренд: Philips Страницы: 11

Бренд: Philips Страницы: 24

Бренд: Philips Страницы: 255

Бренд: Philips Страницы: 40

Бренд: Philips Страницы: 215

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды