Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 16

Страница: 16 / 114

Chapter 1

www.aerotech.com

Table 1-1:

Feature Summary

Standard Features

85 - 240 VAC control supply inputs

Section 2.2.1.

240 VAC (max) motor supply inputs

Section 2.2.2.

Primary quadrature encoder input channels

Section 2.4.1.

Absolute Encoder support

Section 2.4.1.2.

Dedicated Home and Limit inputs

Section 2.4.5.

Dedicated 5-24 V Emergency Stop sense input

Section 2.5.

Auxiliary quadrature encoder input channels

Section 2.6.1.

Single-axis PSO capability

Section 2.6.2.

Four digital outputs (opto-isolated)

Section 2.6.3.

Four digital inputs (opto-isolated)

Section 2.6.4.

Two high-speed digital inputs (opto-isolated)

Section 2.6.5.

One 16-bit analog output (±10 VDC)

Section 2.6.6.

One 16-bit analog differential input (±10 VDC)

Section 2.6.7.

One 24 VDC, 1 A brake relay

Section 2.7.

Table 1-2:

Ordering Options

Options

Power Stage Options (

Section 1.2.

)

50-S

50 A peak; 25 A continuous; 440 W continuous internal shunt resistor; requires
FAN-115 or FAN-230 option

75-S

75 A peak; 37.5 A continuous; 440 W continuous internal shunt resistor; requires
FAN-115 or FAN-230 option

100-S

100 A peak; 50 A continuous; 440 W continuous internal shunt resistor; requires
FAN-115 or FAN-230 option

I/O (

Chapter 3

) and Feedback (

Section 2.4.1.3.

) Options

-IO

Expansion board with 16 digital inputs (opto-isolated); 16 digital outputs (opto-
isolated); three 16-bit differential analog inputs (±10 V); three 16-bit analog outputs
(±10 V); 2 SSI Net; absolute encoder interface; one mechanical brake relay

-MXH

Programmable encoder multiplier up to x16384 (x65,536 after quadrature);
supports single/dual axis PSO and real-time encoder quadrature output

PSO Options (

Section 3.2.

)

-DUALPSO

Two axis Position Synchronized Output (PSO)

-TRIPLEPSO

Three axis Position Synchronized Output (PSO); requires I/O option

-PSONC

Normally closed PSO output (default normally open); requires I/O option

Ethernet Option (refer to the Help file)

-ENET

10/100 BASE-T Ethernet port for use with Ethernet I/O modules

Ndrive HPe 50/75/100

Introduction

Содержание Ndrive HPe 100



















































































































Результаты поиска

Содержание Ndrive HPe 100

Отзывы:

Похожие инструкции для Ndrive HPe 100

Бренды по названию

Популярные бренды

Aerotech Ndrive HPe 100, Руководство по оборудованию

Результаты поиска

Содержание Ndrive HPe 100

Отзывы:

Похожие инструкции для Ndrive HPe 100

Бренды по названию

Популярные бренды