manualshive.com logo in svg

Aerotech Ndrive HPe 100, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 60

60

Chapter 2

www.aerotech.com

2.6.3. Digital Outputs 8-11 (J205) 

The digital outputs are optically-isolated and can be connected in sourcing or sinking configurations. The
digital outputs are designed to connect to other ground referenced circuits and are not intended to provide
high-voltage isolation.

The outputs are software-configurable and must be connected in either all sinking or all sourcing mode.

Figure 2-28

and

Figure 2-29

illustrate how to connect to an output in current sourcing and current sinking

modes.

The opto-isolator's common connections can be directly connected to the drive's power supply; however,
doing so will effectively defeat the isolation and will reduce noise immunity.

Table 2-27:

Digital Output Specifications

Opto Device Specifications

Value

Maximum Voltage

24 V maximum

Maximum Sink/Source Current

60 mA/channel @ 50°C

Output Saturation Voltage

2.75 V at maximum current

Output Resistance

33 Ω

Rise / Fall Time

250 usec (typical)

Reset State

Output Off (High Impedance State)

Table 2-28:

Digital Output Pins on the Auxiliary I/O Connector (J205)

Pin#

Description

In/Out/Bi

7

Digital Output 8

Output

8

Digital Output 9

Output

9

Digital Output 10

Output

15

Output Common

-

16

Digital Output 11

Output

Ndrive HPe 50/75/100

Installation and Configuration

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды