Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 114

background image

Installation and Configuration

Ndrive HPe 50/75/100

2.4.1. Encoder Interface (J207)

The Ndrive HPe 50/75/100 is equipped with standard and auxiliary encoder feedback channels. The
standard encoder interface is accessible through the Motor Feedback (J207) connector. The standard
encoder interface will accept an RS-422 differential line driver signal. If the Ndrive HPe 50/75/100 has been
purchased with the -MXH option, the standard encoder interface can be configured for an analog encoder
input via parameter settings.

Refer to

Section 2.4.1.4.

for encoder feedback phasing. Refer to

for the auxiliary encoder

channel.

N O T E :

Encoder wiring should be physically isolated from motor, AC power, and all other power wiring.

Table 2-10:

Encoder Interface Pins on the Motor Feedback Connector (J207)

Pin#

Description

In/Out/Bi

1

Chassis Frame Ground

N/A

3

+5V Power for Encoder (500 mA max)

Output

6

Encoder Marker Reference Pulse -

Input

7

Encoder Marker Reference Pulse +

Input

14

Encoder

Input

15

Encoder Cosine -

Input

17

Encoder Sine +

Input

18

Encoder Sine -

Input

21

Signal Common for Encoder

N/A

www.aerotech.com

Chapter 2

39

«
...
37
38
39
40
41
...
»

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ndrive HPe 100

Бренд: Fagor Страницы: 56

Бренд: NI Страницы: 42

Бренд: GFA Страницы: 21

Бренд: SOMFY Страницы: 27

Бренд: IEF Werner Страницы: 48

Бренд: Kone Страницы: 42

Бренд: Becker Страницы: 28

Бренд: Becker Страницы: 44

Бренд: LS Industrial Systems Страницы: 127

Бренд: SAF Страницы: 38

Бренд: Leadshine Technology Страницы: 8

Бренд: Becker Страницы: 8

239-03-00 Series

Бренд: Vicon Страницы: 27

Falk Drive One D Series

Бренд: Rexnord Страницы: 16

Бренд: YASKAWA Страницы: 102

Бренд: Fagor Страницы: 386

Бренд: ABB Страницы: 48

Бренд: Eaton Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды