Advantage Controls MegaTron Series Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 23

Advantage Controls MegaTron Series Скачать руководство пользователя страница 3

I. Introduction

The MegaTron microprocessor based controllers are designed to provide a wide range
of control functions for recirculating water treatment systems. The controller is
programmed through a front panel keypad and can be configured to provide a
customized control system for your application. Your particular unit’s functions can be
determined be comparing the units model number to the Model Numbering Table (see
page 3).

☼

Notice:

Depending upon the options supplied on your unit you may or may not

have all features and functions described in this manual.

Model Numbering

MegaTron units have several base system control functions and unit optional features.
Your unit may be supplied with one or more of the features described in this manual. To
determine what features apply to your unit check the model number label located on the
controller enclosure.

Base System Control Functions

Optional Features

C -

Tower Conductivity Control

A

- Conduit connections

B -

Boiler Conductivity Control

D

- Dry Contact relays

M -

Make-up Conductivity

H

- Remote Communications bus only

P -

pH Control

H1

- Direct Connect Communications

R -

ORP Control

H2

- Internet Connect Communications

T

- Temperature Control

J

- Additional System Card bus only

F1

to

F5-

Chemical Feed Timers

K

- Additional Control Relays

E

- Flow Switch Assembly

Y

- ETL Agency Listing / Approvals

L1

to

L5

- Drum Level Alarm Inputs

A model number will start with

MG

and will be followed with the Base System Control

functions. If the unit is a dual system, all of the control functions of system one are
followed by a

dash

then the functions for system two. If system two is the same as the

first a (–X2) is used. Another

dash

separates the optional features listed after all base

system control functions.

Example Model Number:

MGCPF3E-X2-DHY

☼

Note:

This list represents our most popular options additional options codes are

available and may appear consult factory if any questions arise.

Description of Unit

MegaTron controllers may be configured to control one or two separate systems
including cooling tower and boiler applications and may have various features depending
on the model number. Whether the unit is controlling 1 or 2 systems each individual
system can be configured with a variety of the functions / features listed below and there

3

«
1
2
3
4
5
...
»

Содержание MegaTron Series
























Отзывы:

Нет отзывов