Advantage Controls MegaTron Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 23

Advantage Controls MegaTron Series Скачать руководство пользователя страница 13

match, key in the correct ORP value, and push ENTER. Press the SETUP/RUN
key to resume normal operation.

There are limits to how much the calibration can be adjusted. The instrument will only
accept new conductivity values which are from 1/2 to 2x the present reading. Any entry
outside this range will cause a default to the original reading. If this happens, call 1-800-
743-7431 for technical assistance.

V. Menu

Navigation

To access the menus press the

Set Up / Run

key on the front panel. This takes you to the

Home

menu. MegaTron controller’s menus are easily navigated by selecting your desired

menu move by pressing the associated number key next to a menu box on the screen.
Once you have stepped through the sub menus to reach a point at which a value or
selection is made a Pop-up window will appear prompting you to enter a desired value or
selection.

☼

NOTE:

When entering new numeric values, enter all available digits (characters).

1.

Home Menu

From the

HOME

menu select the desired menu.

The menu name explains what parameters can
be programmed in the menu.

>HOME SETUP<

SETPOINTS

DATE/TIME

CALIBRATION CONFIGURE
TIMERS HISTORY

CUSTOMIZE WATER METER

ALARMS RELAYS

SET POINTS

-

Setting control set points for conductivity, temperature, pH and ORP.

CALIBRATION

- Calibrating conductivity, temperature, pH and ORP if present.

TIMERS

-

Menu for selecting type and settings for all present feed timers.

CUSTOMIZE

-

Giving the controller, each system and all relays a user defined name.

ALARMS

-

View current alarms.

DAY/TIME

-

Menu for setting date and time.

CONFIGURE

-

Menus for configuring passwords, relay activations, digital inputs, setting
history interval, flow switch, contrast, temperature scale.

HISTORY

-

Allows for view history on board in a graph form.

WATER METER

-Menu for configuring water meter totalizing.

RELAYS

-

Menu for resetting accumulated "ON" times and manual activation.

13

«
...
11
12
13
14
15
...
»

Содержание MegaTron Series
























Отзывы:

Нет отзывов