Advantage Controls MegaTron Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 23

Advantage Controls MegaTron Series Скачать руководство пользователя страница 19

9. History

The onboard history allows for viewing the history of the probe readings, relay activations,
key pad activity, calibrations and alarm logs for each system present. An initial overview
page is displayed showing your current sample interval, the calculated number of days the
unit can keep probe history for before loosing the oldest. The number of sensor samples
and relay/alarm events currently stored is also displayed.

Note:

The history can be reset by going to

the configure menu and entering a different
sample interval. After the new sample
interval has been entered you can then re-
enter your desired sample interval.

>HISTORY REVIEW<

SYSTEM 1

Sample Time: 5 MIN

(Length 164.62 days)

Sensor Samples

882

Relay/Alarm Events

323

9.1

Viewing History

RELAY LOGS-

Relay activations displayed

in a log form. Arrow up to advice through
the log.

>HISTORY<

RELAY LOGS
ALARM LOGS
SENSOR HISTORY

EVENT LOG

ALARM LOG-

Alarm activations displayed

in log form.

SENSOR HISTORY-

For selecting the

parameters and viewing of a given probe
reading’s history in log or graph form.

EVENT LOG-

Displays various keypad

activities.

10. Water

Meters

WATER METERS –

Shows the water meter

input records (totalizer) and defines the contact
value (100) and units of measure (gallons).

>WATER METERS<

SYS 1 WATER METER 1
SYS 1 WATER METER 2

SYS 2 WATER METER 1

SYS 2 WATER METER 2

11. Relays

>RELAYS<

RELAYS 1-10 STATUS

RELAYS 1-10 RESET

STATUS–

Allows for viewing accumulated relay

ON times, forcing relays ON or OFF or seeing
which relay is on.

RESET-

Allows for the resetting to zero the

accumulated run time of a particular relay.

19

«
...
17
18
19
20
21
...
»

Содержание MegaTron Series
























Отзывы:

Нет отзывов