manualshive.com logo in svg

Advantage Controls MegaTron Series, Техническое руководство по установке и обслуживанию, Страница: 17 / 23

Поделиться
Скачать
Advantage Controls MegaTron Series Скачать руководство пользователя страница 17

4.7       28-Day Timer 

 
Each 28-day timer has a Program 1 and a Program 2 for programming the various feed times.  
The programming for Program 1 and 2 are the same but allow for more variation in the timer’s 
relay activation. 

 

WEEKS-

 The week(s) that the timer is to feed. 

DAYS- 

The day(s) that the timer is to feed. 

START-

The time of day for the timer to start. 

RUN-

 How long the timer is to run. 

PREBLEED-

How long the controller is to 

bleed down before feeding in chemical.  
NOTE: The prebleed starts at the START 
time programmed above. 

>SYSTEM 1 TIMER 1 CHANGE< 

WEEKS    

MIN 

COND 

DAYS 

   FEED 

LOCK 

START TIME 

    BLEED LOCK 

RUN 

TIME 

  FLOW 

LOCK 

PREBLEED

 

MIN COND-

The minimum conductivity that 

the unit will prebleed down to. 

FEED LOCK-

Which other system timer to 

lockout during this timers run time. 

BLEED LOCK-

How long to lock out the 

bleed function after the timer’s run time. 

FLOW LOCK-

If the system has a flow 

switch you can ignore it for this timer. 

 

5.  

Customize

 

 
 

>CUSTOMIZE< 

UNIT NAME 
SYS 1 NAME  

SYS 2 NAME 
RELAY NAMES 

 

 
CUSTOMIZE – 

Allows for the user to define the 

on-screen name for the Unit, System 1 and 
System 2 (if applicable) as well as the names for 
each relay. 
 

 
 
6. Alarms 

 

ALARMS – 

Shows any current alarms. 

 
 
 
 
 
 
 

 

>ALARMS< 

SYS 1 ALARMS 

SYS 2 ALARMS 
 

 
 

 

 

 

 
7. 

Date and Time Set Up 

 

>SET DATE AND TIMES< 

SET DATE 

SET TIME 
SET DAY 

SET WEEK 
Friday May 18, 2002 03:04:56 

DATE AND TIME - 

 For setting the date, 

time, day and week on the controller. 
 
 
 
 

 

17 

Содержание MegaTron Series
























Отзывы:

Нет отзывов