ADT A-ADRP16E-320 Скачать руководство пользователя страница 15

Страница: 15 / 94

Digital Video Recorder

Connecting the Monitor

Figure 7 — Video Out connectors.

Connect the monitor to either the

Video Out

SVHS Out

connector.

Connect the spot monitor to the

SPOT

connector if required.

NOTE: If your monitor has an SVHS input, use it because it will give you better quality
video display.

NOTE: The

Video Out

(BNC) and the

SVHS Out

connectors may be connected to

individual monitors for simultaneous operation.

Connecting Audio

NOTE: It is the user’s responsibility to determine if local laws and regulations permit
recording audio.

Figure 8 — Audio In and Out connectors.

Your DVR can record audio. Connect the audio source to Audio In. Connect

Audio Out

your amplifier.

NOTE: The DVR does not have amplified audio output, so you will need a speaker with
an amplifier. The audio input can be from an amplified source or directly from a
microphone.

NOTE: When connecting the observation camera with built-in microphone, the audio
from that camera is heard on the DVR speaker or audio output.

Содержание A-ADRP16E-320































































































Результаты поиска

Содержание A-ADRP16E-320

Отзывы:

ADT A-ADRP16E-320, Руководство пользователя, Страница: 15 / 94

Результаты поиска

Содержание A-ADRP16E-320

Отзывы: