ADJ Products, LLC - www.adj.com - Vizi Beam Hybrid 2R Instruction Manual Page 18
Slave Mode - This function lets you designate the unit as the slave in
a Master-Slave configuration.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Slave Mode” is displayed,
and press ENTER.
3. Either Slave 1, Slave 2, or Slave 3 will be displayed. Press ENTER
to select either of the three, or press MODE/ESC button to exit.
Auto Program - This function allows the internal programs to run in
either stand-alone or master/slave mode. In “Master” mode the fix-
ture will send DMX data to other fixtures connect via the DMX chain.
In “Alone” mode the fixture will operate as a single fixture. The pro-
gram for this mode is selected in the “Select program” section of
the control menu. You can set the number of steps under “Edit pro-
gram”. You can edit the individual scenes under “Edit scenes”. With
this function, you can run the individual scenes either automatically,
i.e. with the adjusted Step-Time.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Auto Program” is displayed,
and press ENTER.
3. Either “Master” or “Alone” will be displayed.
4. Press ENTER to to make your selection, or press MODE/ESC
button to exit.
Sound Control - With this function, the internal program will run in
sound active mode.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Sound Control” is dis-
played, press ENTER.
3. Either “Master” or “Alone” will be displayed. Use the UP or DOWN
buttons to change the operating mode.
Vizi Beam Hybrid 2R
System Menu
ADJ Products, LLC - www.adj.com - Vizi Beam Hybrid 2R Instruction Manual Page 41
Vizi Beam Hybrid 2R
Operation
DOWN buttons select “Alone” and press ENTER.
Master-Slave Operation (Sound Active or Auto Program):
This function will allow you to link up to 16 units together and oper-
ate without a controller. The units can run a built-in program or run in
sound actiive mode. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units pro-
grams. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR
connector is the output. The first unit in the chain (master) will use
the female XLR connector only - The last unit in the chain will use
the male XLR connector only. For longer cable runs we suggest a
terminator at the last fixture.
2. On your “Master” unit, access the main menu, and press the UP
or DOWN buttons so that “Function” is highlighted, then
press ENTER.
3. Select your desired operating mode. Use the UP or DOWN but-
tons to select between “Auto Program” or “Sound Control”,
press ENTER to select your desired program.
4. Either “Master” or “Alone” will be displayed. Using the UP or
DOWN buttons select “Master” and press ENTER.
5. For your “Slave” units, access the main menu, and press the UP
or DOWN buttons so that “Function” is highlighted, then
press ENTER.
6. Press the UP or DOWN buttons until “Slave Mode” is displayed,
and press ENTER.
7. Either Slave 1, Slave 2, or Slave 3 will be displayed. Select your
desired Slave setting and press ENTER.
5. Press MODE/ESC if you want to return to the main menu.
6. You may change the show or invert the pan and tilt functions
in the system menu by following the directions on pages 26-27.
